TRANSPONDER MAKER PRO 2

Transponder Maker Pro 2 (TMPro2) is transponder programming tool,
key copier and PIN calculator in one.

Hardware is small box, which have to be connected to free PC USB port.
Software supports 10 languages - Bulgarian, English, French,
Portuguese, Polish, Hungarian, Spanish, Serbian, Italian and Czech.

It is simply to use and offer wide range of supported immoboxes and keys.
TMPro2 is designed to help in locksmith`s job.

TMPro2 is organized as modular software.
This means that every supported immobox is separate module.
At beginning you can purchase hardware and only one module.
In future you can add new modules by simple module purchasing system. 

TMPro2 works with immobilisers eeprom dumps.
You must have electronic knowledges and to know how to use
soldering-desoldering tools and memory devices programmers.
It is your choice what programmer you will use for reading memory devices.

In order to use TMPro2 you have to remove immobox or BSI/UCH unit from car,
open it, desolder and read specific memory device, which contain needed key information.
Safe eeprom area into BIN or EEP format.
Then solder back memory device, reassemble immobox and fit back to car.
Use saved file with TMPro2 to program transponder.
In information box is shown type of memory device and what is correct lenght of readed file.
Depending of immobox it may be serial eeprom, Motorola MCU or
Texas Instruments MCU.

You can use any proper programmer to read data from it.
TMPro2 works only with BIN or EEP files.
It automatically recognises immobox by opening eeprom file of it.
For modules, which use serial eeprom 93cXX software automatically recognises if dump is readed correctly (x8 or x16), and if needed, swap bytes.

If file is of known size and type, software automatically goes to correct module.
If file size or type is not recognised, software not goes to desired module.
Anyway if file size is known, you still can program transponder, but in this case written transponder is possible not to contain proper data to start car. 
TMPro2 uses 7 types of transponders.
In information box below module picture is shown what transponder have to be used with selected module.

Used types are:
Sokymat Nova, also known as Silca T5 or JMA TP05.
Philips PCF 7935. You can use also Silca T15 or JMA TP14.
Philips PCF 7936. You can use also Silca T14 or JMA TP12.
Sokymat Magic, also known as Megamos Crypto.
You can use also Silca T6 or JMA TP08.
JMA TPX1 or Errebi TX1
JMA TPX2 or Errebi TX2
Texas DST, also known as Texas Crypto or Silca 4D-60 - JMA TP06/TP19 

TMPro2 features

INDEPENDENT solution for Fiat/Alfa Romeo/Lancia/Peugeot/Citroen CODE2 cars.
This means all vehicles 1999 up to date, which use precoded by chassis number keys
with Megamos Crypto transponder (ID48).
NO MORE need to order keys from dealer and to wait for them.
Using Fiat CODE2 modules (6,7,8,9,45,48,59,100) software prepares chip and shows PIN code -
all you have to do is to program key into car.

INDEPENDENT solution for Alfa Romeo 156/166 cars,
which uses PCF7935 transponders (ID44).
Using Alfa 156/166 module (5) software prepares PCF7935 transponder.
You DO NOT need any futher operations -
just fit chip into key and start vehicle.
If old keys are erased, software shows PIN code and prepares transponder,
ready to be matched with vehicle using diagnostic device. 

INDEPENDENT solution for Renault/Opel Vivaro/Dacia Logan UCH cars.
This means all vehicles which uses keys and 12 - digit PIN code.
NO MORE need of expencive remotes.
Using Renault UCH modules (30,31,44,57) software prepares PCF7936 chip and shows PIN code -
all you have to do is to program key into car.
Also if you KNOW 12 - digit PIN code, you DO NOT need to read
eeprom from UCH module.
You can make DIRECT chip preparing using corresponding module and PIN code. 

INDEPENDENT solution for Iveco Daily and Iveco Trucks,
which uses keys with ID46 transponders.
NO MORE " Sorry, we can`t supply your PIN code, you have to buy new full set".
NO MORE need of expencive Iveco keys.
Using Iveco module (36) software converts PCF7936 chip into
ready to be programmed into any Iveco van or truck.
If you KNOW pin code, you DO NOT need to open and read immobox,
just prepare chip and program it into vehicle.
In case you don`t know it, read immobox eeprom and software will
calculate and show it.  

INDEPENDENT solution for Ford and Mazda vehicles,
which use OUTCODE-INCODE system (so called CODED ACCESS).
NO MORE need testers and stable Internet connection while doing key programming.
Using Ford and Mazda modules (69,70,72,73,74,81,82,84,89, 106) software programs
JMA TPX2 - Errebi TX2 chip ready to start vehicle.

SOLUTION for Yamaha, Suzuki, Kawasaki, Ducati, Honda, Aprilia, BMW, Peugeot and Piaggio bikes.
NO MORE need to search for bike ECUs,
which do not have immobiliser function and to rearrange bike wiring.
Using modules 25,33,58,66,67,68, 96, 97, 98, 101, 108, 109 software prepares chip,
ready programmed to start bike.
For Yamaha bikes there is solution for both variants - with eeprom 66 and with Moric MCU 108  
KEY COPIER modules (62,63,64, 65) help you to copy
all of Philips/Megamos/Temic fixed keys (ID11,ID12,ID13,SAAB,ID33) and also
Philips ID41,ID42,ID44 VAG,ID45 and Texas 4C and 4D crypto keys.
NO NEED ANY SPECIAL PRECODED CHIPS,simply T5,PCF7935,JMA TPX1 and JMA TPX2.
JMA TPX1 you can reprogram many times, JMA TPX2 once locked cannot be reprogrammed.
In addition you can see vehicle PIN code for Renault ID33 keys (module 62),
Renault Megane/Scenic ID4D keys (module 65) and
for Peugeot 206/406 ID45 keys (module 63).

IMPORTANT NOTE: Module 65 requires JMA TPX cloner for to work.

You must contact with nearest JMA dealer. 

SOLUTION for Renault Megane/Scenic vehicles,
which use Texas crypto 4D chip in key.
Using modules 79 and 80 you can program JMA TPX2 - Errebi TX2 chip and car starts.
In addition software shows 8-digit PIN code in case
you need to erase old keys from vehicle with diagnostic device.

SOLUTION for Scania, Volvo, Mercedes, DAF, MAN and Renault trucks.
NO NEED to wait for dealer to come, moreover some of dealers need truck to be towed to them.
Using modules 34, 37, 51, 53, 88 and 93 software prepares chip,
ready programmed to start truck. 

SOLUTION for SAAB 9-3 and 9-5 vehicles 1998-2003.
When all the keys are lost, the only solution is to buy new very expencive TWICE unit from dealer.
NO MORE - using module 47 software prepares T5 chip, ready programmed to start vehicle.  
UNLOCKER of locked ID48 chips.
After programming on vehicle,
most of ID48 keys become locked and cannot be used again on other vehicle.
Now with TMPro2 you can unlock them.
NOTE: not all ID48 chips can be unlocked,
try and if you have a luck you will get unlocked chip.
The ID48 unlocker is free function.  

IDENTIFIES AND SHOWS data for all transponders on market -
ID11, ID12, ID13, SAAB, ID33, ID40, ID41, ID42, ID44, ID45, ID46, ID48, ID4C, ID4D, ID73, ID8C, ID8E
For Philips it shows to which car manifacturer it belongs -
VAG, Opel, Peugeot/Citroen, Renault(shows 4-digit PIN code), Mazda, Alfa Romeo, Honda, Volvo/Mitsubishi, Nissan etc.
For Opel ID40 it shows if chip is not locked or already programmed to car (locked).
For ID48 shows if is locked or not, there is possibility for unlocking.
For ID4D shows content of all pages and also if particular page is locked or not.
For BMW ID73 key and Hitag2 CAS keys reads mileage, stored in key.
For BMW HITAG2 CAS keys you can change mileage, stored in key.
Reading and identifying keys is free function.

READY to START CAR transponders in 80% of modules.
Avoid needs of PIN codes and key programming procedures.

You can check what more can offer TMPro2 for your locksmith`s job:

    TMPro2 saves your time. If you have coleague, which main job is to remove and refit locks and immoboxes, with TMPro2 you will not need to go to car to do key programming.This is applied for modules, which prepare ready to start car transponders. You can check this in information box below immobox picture. Just read immobox dump and using TMPro2 write transponder. This also means, that you do not need PIN codes anymore for these immoboxes. Your coleague refit immobox and lock and car is ready to start. You do not need to go to car to match key anymore.

    TMPro2 lowers your costs for original keys or remotes. Some cars like Renault,Fiat and Iveco accept for programming only expencive specific remotes and keys. NO MORE - now with one click on PROG button you can convert common transponder into ready to be matched with car.

    TMPro2 reduces time for finishing locksmith job. BMW,Fiat,Alfa Romeo and Lancia cars uses only preprogrammed by chassis number keys and you have to offer from dealer and wait for them. NO MORE - now using eeprom dump, readed from memory device and one click on PROG button you can program into transponder specific information anf it become ready to start or to be matched with particular car. Also you get PIN code, needed for key matching procedure.

    TMPro2 gives more independence in locksmith`s job. Vehicles, which uses transponders in keys can be divided into 2 groups. First is which not use PIN code. Second is which use PIN code. For second group you have to order PIN code by chassis number, to pay and to wait for it. Sometimes supplied PIN code is not correct. Also for some vehicles you have to order precoded by chassis number keys. All this steps can be bypassed, if your immobiliser is supported by TMPro2. For 80% of modules TMPro2 prepares from immobox eeprom dump ready to start car transponder and you do not need any futher operations. Just cut newkey, put written transponder in it and start car. For the rest 20% of modules software shows immobiliser PIN code and you have to match written transponder with car. You can use key programming devices such as AD100, DEC Superscan or similar.

Top